Applied-motion ST10-Si-NE User Manual download pdf

Serial No

Error Codes

GR-Green RD-RED

POSITION LIMIT 1 GR + 1 RD

CCW LIMIT TRIP 1 GR + 2 RD

CW LIMIT TRIP 2 GR + 2 RD

DRIVE OVER TEMP 1 GR + 3 RD

MOTOR OVER TEMP 2 GR + 3 RD

VOLTAGE HIGH 1 GR + 4 RD

VOLTAGE LOW 2 GR + 4 RD

OVER CURRENT 1 GR + 5 RD

HALL FAIL 1 GR + 6 RD

ENCODER FAIL 2 GR + 6 RD

COMM ERROR 1 GR + 7 RD

Front View

X COMMON

X7 / CW Limit

X3 / Servo Enable

X4 / Alarm Reset

Analog IN-

Analog IN+

X2 / DIR-

X2 / DIR+

X1 / STEP / PWM+

X1 / STEP / PWM-

GND

A+

A-

B+

B-

Z+

Z-

+5V OUT

Y COMMON

Y3 / ALARM

Y2 / INPOSN

Y1 / BRAKE

edocnE

stuptuO

X6 / CCW Limit

IN/OUT 1

ST5-Q

ST5/10-Si Quick Setup Guide

Requirements

▪ A compatible stepper motor.

▪ A small at blade screwdriver for tightening the connectors (included).

▪ A personal computer running Microsoft Windows 95, 98, NT, Me, 2000, XP, Vista or 7.

▪ Si Programmer™ software, available at: http://www.applied-motion.com

▪ An Applied Motion programming cable (included).

▪ For more detailed information, please download and read the ST5/10-QSiC Hard-

ware Manual, available at www.applied-motion.com/support/manuals.

To begin, make sure you have the following equipment:

Step 1

a) Download and install the Si Programmer™ software.

b) Launch the software by clicking:

Start / Programs / Applied Motion Products / Si Programmer

c) Connect the drive to your PC using the appropriate programming cable.

Step 2

Warning - If you are using a non-Applied Motion motor, do not connect the mo-

tor until after you have congured the drive for your motor. Refer to Step 5.

a) Wire the drive to the DC power source.

(do not apply power until all connections to the drive have been made)

Note, the ST5-Si accepts DC voltages from 24-48V,

while the ST10-Si accepts DC voltages from 24-80V.

b) Ensure a proper earth ground connection by using the screw on the left

side of the chassis.

If using an external fuse, we recommend the following:

ST5-Si: 3AG, 4 amp (Littlefuse 313004P)

ST10-Si: 3AG, 6.25 amp (Littlefuse 3136.25P)

See the ST5/10-QSiC Hardware Manual for more information about

power supply and fuse selection.

Connection Panel

920-0008 C

1 2

ST5/10-Si Quick Setup Guide 1

Summary of Contents

Page 1 - ST5/10-Si Quick Setup Guide

Serial NoError CodesGR-Green RD-REDPOSITION LIMIT 1 GR + 1 RD CCW LIMIT TRIP 1 GR + 2 RDCW LIMIT TRIP 2 GR + 2 RDDRIVE OVER TEMP 1 GR +

Page 2

Step 3If you have any questions or comments, please call Applied Motion Products Customer Support:(800) 525-1609, or visit us online:www.applied-motio

Related models: ST10-Si-NF | ST10-Si-NN | ST5-Si-NE | ST5-Si-NF | ST5-Si-NN |

Comments to this Manuals

No comments

Applied-motion ST10-Si-NE User Manual

Browse online or download User Manual for Hardware Applied-motion ST10-Si-NE. Applied Motion ST10-Si-NE User Manual

Summary of Contents

Related models: ST10-Si-NF | ST10-Si-NN | ST5-Si-NE | ST5-Si-NF | ST5-Si-NN |

Comments to this Manuals

Related products and manuals for Hardware Applied-motion ST10-Si-NE